Forum: Annotation
08-06-2007, 09:01 AM
|
Replies: 7
Views: 6,131
Re: Copy view
I looked for create dependent general view in the create view menu and I don't see it anywhere. Where might it be? I am using 13.01.
Thanks,
Mark
|
Forum: Annotation
08-06-2007, 05:27 AM
|
Replies: 7
Views: 6,131
Re: Copy view
OK I was able to just create another general view using the same direction as the view UI had just previously created (right click in direction bar and select the previous direction numbers). However...
|
Forum: Annotation
08-06-2007, 05:02 AM
|
Replies: 7
Views: 6,131
Re: Copy view
Bump...any answer for this? I would like to do the same, removing some parts on one view for a clearer picture. Again this is for general views.
M.Fitzpatrick
|
Forum: Annotation
04-26-2007, 03:23 AM
|
Replies: 1
Views: 3,684
|
Forum: CoCreate Modeling
07-26-2006, 07:48 AM
|
Replies: 4
Views: 3,251
Re: Splines
Hey I just found it, under my overdraw menu. All set now.
Mark
|
Forum: CoCreate Modeling
07-26-2006, 07:46 AM
|
Replies: 4
Views: 3,251
Re: Splines
Believe it or not if I hadn't added the create splines to my customized menu I don't even see a command to create them in my 2d menu.
So NO I am not seeing what you are. I have modeling 2005 13.01....
|
Forum: CoCreate Modeling
07-26-2006, 06:49 AM
|
Replies: 4
Views: 3,251
Splines
OK so I finally get to use create 2d spline. Well I have created the spline and would like to move the control points to fine tune the spline. Well according to the help menu I should select the...
|
Forum: Annotation
02-15-2006, 11:17 AM
|
Replies: 2
Views: 2,275
|
Forum: Annotation
02-15-2006, 06:01 AM
|
Replies: 2
Views: 2,275
paper space to annotation
I am trying to load files created in Autocad under paper space. When I load them in annotation all I get is a blank page. I was told this is because they were made in paper space not solid mode of...
|
Forum: Annotation
10-28-2005, 10:00 AM
|
Replies: 3
Views: 3,664
Re: Saving multi sheet .mi as dxf
OK I found that only a single sheet can be saved as a dxf.
Anyway we can get all the sheets to show on one page, one above or beside the other in a single file dxf?
Mark
|
Forum: Annotation
10-28-2005, 09:52 AM
|
Replies: 3
Views: 3,664
Saving multi sheet .mi as dxf
What ever sheet is active is what that comes up in the dxf, not all sheets. Is that the way its supposed to work? Can there be multisheet dxf files?
Kind of a pain saving each sheet individually and...
|
Forum: Annotation
10-28-2005, 09:50 AM
|
Replies: 5
Views: 4,253
Re: Importing dxf
I think its an across the board problem since I saved the file under multiple formats and it imported the same way, be it dwg release 12 or whatever. Maybe its something hidden lower in the dwg but...
|
Forum: Annotation
10-25-2005, 05:00 AM
|
Replies: 5
Views: 4,253
Re: Importing dxf
Bump- any solution for this yet?????????
Or just yet another bug?
Mark
|
Forum: Annotation
08-12-2005, 10:15 AM
|
Replies: 5
Views: 4,253
|
Forum: Annotation
08-12-2005, 05:51 AM
|
Replies: 5
Views: 4,253
Importing dxf
I'm trying to import a dxf or dwg and some of the the dimensions come in at an angle.This happens in drafter or designer annotation.
Any ideas?
Mark
|
Forum: Annotation
06-24-2005, 05:18 AM
|
Replies: 5
Views: 5,175
Re: Two gripes...
Steve that is not the only dimension that still moves when you update. I have found diameter dimensions to move also. Used to be radius and chamfer dimension too, but as of yet I haven't seen them...
|
Forum: Annotation
06-17-2005, 06:22 AM
|
Replies: 6
Views: 4,380
Re: Association loss
Nope it was associative to start and lost it after I deleted two detail views.
Wierd.
Mark
|
Forum: Annotation
06-17-2005, 06:19 AM
|
Replies: 2
Views: 3,300
|
Forum: CoCreate Modeling
06-17-2005, 06:17 AM
|
Replies: 5
Views: 4,271
Re: More Version 13 Requests
Dorathea,
Co-create came to give a demonstartion and answer some questions about the new version. They told us we needed the next pkg up to have the hoover over edge option. I guess we have the...
|
Forum: CoCreate Modeling
06-07-2005, 07:24 AM
|
Replies: 5
Views: 4,271
Re: More Version 13 Requests
Yes I read them. Apparently our basic "non proffesional" version doesn't support the hoovering over an edge option. I also do not see any option that replaces or makes selecting the same direction I...
|
Forum: CoCreate Modeling
06-07-2005, 06:22 AM
|
Replies: 5
Views: 4,271
More Version 13 Requests
Can anyone tell me why in the world the face minus normal, face normal and edge tangent options have been removed from this software???? Defining directions for measuring and or moving used to be so...
|
Forum: Annotation
06-03-2005, 08:45 AM
|
Replies: 6
Views: 4,380
Re: Association loss
When I first loaded the model and drawing all was fine, I updated ok too. Then after I deleted a couple detail views and went to update I noticed the associativity was lost. That is all I did,...
|
Forum: Annotation
06-03-2005, 08:03 AM
|
Replies: 6
Views: 4,380
Re: Association loss
Why would I have had to reload the model? Nothing was changed with it in the coarse of what I was doing.
Mark
|
Forum: Annotation
06-03-2005, 04:50 AM
|
Replies: 6
Views: 4,380
Association loss
OK yesterday I was updating some dwg's and when I loaded solid with dwg the association was gone. I reattached the views and proceeded. Today as I was working on another dwg the dwg became...
|
Forum: CoCreate Modeling
03-31-2005, 03:13 AM
|
Replies: 18
Views: 9,302
|